Consumer Automotive Research Logo
Disclosure
This website is a participant in the Amazon Services LLC Associates Program. We are reader-supported. If you buy something through links on our site, we may earn an affiliate commission at no additional cost to you. This doesn't affect which products are included in our content. It helps us pay to keep this site free to use while providing you with expertly-researched unbiased recommendations.
The Best

3 Inch Lift Kit For Chevy Silverado 1500 4Wd

Handpicked
Quality-Checked
Supreme Suspensions - Front Leveling Kit for 1999-2007 Chevrolet Silverado 1500 + GMC Sierra 1500 3"...
  • COMPATIBLE WITH 1999 - 2007 (Classic) Chevrolet Silverado 1500 (2WD) and 1999 - 2007...
  • CONTENTS: (2x) High-Strength Steel Spring Spacers, Installation Instructions and Supreme...
  • TECHNICAL NOTES: 3 inch front suspension lift. Please note that front spacer thickness to...
  • INSTALLATION: Easy bolt-on installation takes 1 to 2 hours without the need for special...
  • BENEFITS: Improves the look of your truck and increases ground clearance, allowing you to...

Read More About 3 Inch Lift Kit For Chevy Silverado 1500 4Wd

Installing a 3 Inch Lift Kit For Chevy Silverado 1500 4Wd

Do you need a new 3 Inch Lift Kit for your Chevy Silverado 1500? You're not alone. Quite a large number of people have the same question. So, we're going to show you how to install one.

Before you even start, make sure you have the right tool for the job. You will need at least one long wrench set, a drill gun, and a line drill. If you don't have any of those tools, you can use a hammer and chisel. Read through all the instructions that come with your lift kit. Make sure you follow them closely! Once installed, test it out to see if it's working correctly.

Start by mounting the frame rails. Most kits include detailed instructions on how to do this. Next, mount the lower frame rails and tighten the mounting brackets. Make sure they are tight enough by checking them from time to time.

Now, it's time to work on the top. Start by installing the top frame rails and attaching them. You might want to use two or three screws so that they are properly mounted to the front end. Next, attach the side skirts to the front. Make sure to screw them onto the rails.

Once that is complete, you can move on to the rear. First, install the side skirt bottom mounts. Then attach the rear frame rail to the truck bed. Follow all the instructions carefully. Make sure you install all the hardware before you start mounting the trim.

Make sure that your mounting blocks are clean. Paint them before installing them. Apply a little oil to make sure everything works as smoothly as possible. Also, it's recommended to use the right kind of lumber. Use medium-density fiberboard for a stronger framing material.

The last step is to install the side skirts and rear frame rails. Follow all the instructions thoroughly. Make sure you install them in the right way. If you're not sure, then ask for help from an experienced installer. If your installation directions don't seem clear, ask someone from the automotive shop.

After your kit is installed, make sure it is working properly. Make sure all the hardware is tightened properly. Check the tires and make sure they are inflated properly. Use the information in this article to properly install your new kit.

In order to determine how much clearance you will have on your vehicle, you should first turn the key and pull it to the parking position. Next, you should do some research to find out how much clearance you will need. For example, if your bumper requires removal of about seven inches, you would need to remove about seven inches of either side of your car from the ground. If you want, you can also get a friend to help you with this part if you are not sure.

Once your vehicle is parked, you should remove the accessories. Then, you should loosen all the nuts that are holding down the rear frame rail. If you need to, you can make sure that the rail is level by looking at the bottom of the frame rail. When you have the frame rail level, you should bolt it down.

Now you will need to remove the side skirts. Take out the rear side skirts by loosening all of the nuts and bolts. Once they are loose, you should remove the rear side skirts. After you have taken them out, you should install the new lift kit. You will need to make sure that you follow all installation instructions for your lift kit.

Now you should install the new side skirt on your car. You will need to secure it using the supplied hardware. The kit comes with hardware that will go behind the front fender. After you install the hardware, you should run a bead of silicone caulk along the entire length of the side skirt. This will help it to stay in place while you install the other pieces.

Now you will need to attach the front bumper to the car. To do this, you should first look at the backside of your bumper and make sure that it is straight and squared. Then you should install brackets on both sides of the bumper. Next, you will want to bolt everything together. If you need any assistance with installing the parts, you can contact a professional installer.